DIY Slap Bracelets are Easy to Make!

You won't believe how easy information technology is to brand DIY Slap Bracelets. I mean, they seem a little magical with their self-closing power with the pic of the wrist! But they tin be made at home with a few household items.

This slap bracelet craft is better suited for older kids and this project does demand developed supervision.

DIY Slap Bracelets that you can make with measuring tape and duct tape - child arm with slap bracelets — Permit's make our own slap bracelet!

Recall slap bracelets from manner back when? Now yous can brand your own (and become kids to help) with just a few supplies.

It's really fun to make your own jewelry and this one is office toy.

This article contains affiliate links.

How to Make Homemade Slap Bracelets

Supplies Needed

Retractable Measuring Tape (the kind you buy at the hardware store non the fabric store)
Apartment Caput Spiral Driver
Scissors
Decorative Duct Tape

Directions for Slap Bracelet Craft

Step 1

Use the screw driver to remove the outer casing of your measuring tape. Cut off the metallic end of the tape and and then cut a piece that is 6 inches long. You'll need a 6-inch slice for each slap bracelet that you lot want to brand.

Step ii

Use the pair of scissors to round the edges of the piece of measuring record.

DIY Slap Bracelets - step 3 fold the measuring tape back on itself placing the numbers on the outside — Fold the record so when it rolls the numbers are on the exterior.

Step three

Whorl the tape dorsum onto itself, bending it back and then that it rolls with the numbered side upward. Yous'll start to feel it become more malleable. You'll know it'southward ready when you tin slap it onto your wrist and it wraps around it!

DIY Slap Bracelets step 4 cover the measuring tape fully with duct tape cut larger than the tape segment — At present permit'due south decorate your slap bracelet!

Step iv

Cut a piece of duct record but larger than your bracelet. Lay it onto the numbered side of your measuring record, and wrap it around the tape to the dorsum side. Cut a smaller piece to cover the remaining bracelet on the underside.

You can vary the patterns, colors and designs of the duct record to create a whole slap bracelet collection!

DIY Slap Bracelets completed shown in various patterns and colors — Oh all the pretty slap bracelet patterns!

Pace v

At present your bracelets are ready to use! Time to start slapping!

DIY Slap Bracelets finished on child's arm in various patterns and colors — I desire one!

Slap Bracelets Brand Great Gifts

These homemade slap bracelets are the perfect souvenir for a friend. Make them together as friendship bracelets! This is a fun (supervised) craft for a slumber party or tween birthday party.

Create a colorful collection to give to a relative or neighbor. And while you may retrieve of kids for this gift, anyone who might have worn them in the 1990s.

DIY Slap Bracelets are fun to give as gift - two slap bracelets on an arm — Slap bracelets are best when worn together.

Slap Bracelet Danger

Unfortunately, where babyhood crazes go, the worried parents follow. When a four-yr-sometime girl cut her finger on the abrupt metallic edges inside a inexpensive imitation slap bracelet, the Connecticut Department of Consumer Protection recalled all knock-off Slap Wraps. Subsequently more reports of slap bracelets gone wild came pouring in, the bracelets were also banned by schools in the state of New York.
-Bustle

So…please be careful. Cutting metal will leave sharp edges which is one of the reason we recommend only using patterned and colorful duct tape which can easily embrace those sharp edges for safety.

Active Time 15 minutes

Total Time 15 minutes

Difficulty Medium

Estimated Cost $fifteen

Materials

Retractable measuring tape (hardware shop version)
Decorative duct tape

Tools

Flat caput screw commuter
Scissors

Instructions

Using the screw commuter, remove the casing from the retractable hardware shop measuring tape and cutting off the metal finish with scissors.
Cut the measuring tape into 6 inch segments - one for each slap bracelet you want to brand.
Round the edges of the iv end corners with scissors.
Curl the record back onto itself, angle information technology so information technology rolls with the number side upwardly. You lot will get to the point where you tin slap information technology on your wrist (exist careful!).
Cut a piece of decorative duct record merely a little larger than your bracelet segment of measuring tape. Wrap it effectually covering all edges. Cut and fit additional pieces to completely cover the measuring tape.
Time to test it out!

Steps to Make a homemade slap bracelet from a tape measure and duct tape - Kids Activities blog — Hither are the uncomplicated steps to make a slap bracelet at home!

More DIY Bracelets You Can Make from Kids Activities Blog

You have to make these really cool BFF bracelets! They are and then cool and you can customize them so many means.
Bank check out these easy friendship bracelet patterns that kids tin can make.
Make this absurd LEGO bracelet!
Check out how to bend craft sticks to make these super fun craft stick bracelets that are curved!
Let's brand this absurd paper harbinger bracelet.
This is super easy and great for even younger kids…brand pipe cleaner bracelets.
These hairband bracelets are made from a mutual, but unusual material!
This has to exist i of the best childhood crafts, Cheerios bracelets!
How to make rubber ring bracelets. Nosotros honey these!
These dewdrop bracelet ideas are recycled.

What colors and patterns did y'all use for your DIY slap bracelets?

steeleparminquale.blogspot.com

Source: https://kidsactivitiesblog.com/82062/diy-slap-bracelets/